ELectronic ENgineers e-shop
WhatsApp +99470-355-77-72
Вт, 2023-10-03, 15:50
Приветствую Вас Гость
Меню сайта
Категории раздела
Наш опрос
Оцените мой сайт
Всего ответов: 382

Онлайн всего: 1
Гостей: 1
Пользователей: 0
Главная » Для электронщиков разработчиков » Arduino совместимые контроллеры и платы » Arduino Shield

CNC Shield Expansion Board V3 For Arduino

Рейтинг: 5.0/5
8.51 AZN
  • Артикул:
  • Наличие: 0
  • Единица: шт.
Купить сейчас

CNC Shield Expansion Board V3 with Drv8825 A4988 Stepper Motor Driver with Heat Sink For Arduino V3 Engrave For 3d Printer Parts

CNC Shield Board:
1>PWM Spindle and direction pins
2>2 x End stops for each axis (6 in total)
3>Coolant enable
4>Uses removable A4988 or DRV8825 compatible stepper drivers
5>Compact design
6>Stepper Motors can be connected with 4 pin molex connectors or soldered in place
7>Runs on 12-36V DC. (At the moment only the DRV8825 drivers can handle up to 36V so please consider the operation voltage when powering the board.)
8>Please note that this is an unassembled kit and Basic soldering skills are needed
DRV8825 Stepper Motor Driver:
1)*Suitable for driving below 8.2V ~ 45V 2.5A stepper motor
2)*Six different stepping resolutions: full, half, 1 / 4,1 / 8,1 / 16,1 / 32.
3)*A simple steps and direction control interface.
4)*Adjustable potentiometer can adjust the maximum output current, resulting in higher step rate. 5)*Automatic current decay mode detection / selection.
6)*Thermal shutdown circuit, undervoltage lockout, crossover current protection.
7)*Ground short-circuit protection and load short-circuit protection.
8)*DRV8825:20*15*11mm/approx 0.79*0.59*0.43inch(L-W-H) .
9)*Heat Sink: 9*9*5mm/approx 0.35*0.35*0.2inch(L-W-H).
10)*Net weight: 4g
A4988 Stepper Motor Driver:
1>Low RDS (On) Output
2>Automatic current decay mode detection / selection
3>Mix with slow current decay modes
4>Synchronous rectification for low power dissipation
5>Internal UVLO
6>Crossover-current protection
7>3.3 and 5 V compatible logic supply
8>Thermal shutdown circuitry
9>Ground fault protection
10>Load short-circuit protection
11>Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
12>Warning: Connecting or disconnecting a stepper motor while the driver is powered can destroy the driver. (More generally, rewiring anything while it is powered is asking for trouble)
Package Included: 1 x CNC Shield Board
4 x A4988/Drv8825 Stepper Motor Driver(Optional)
4 x Mini Heat Sink(Optional)

Добавил: elektronwik1, Пт, 2020-10-23

Вход на сайт
Ваша корзина пуста

  • 1 AZN = 53.376 Рубль
  • 1 AZN = 15.326TL
  • 10 AZN = $5.872
Copyright WWW.ELEN.AZ Baku Azerbaijan © 2023 Телефон(WhatsApp):+994703557772